注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
请注意：1.只有在红光为一条线的时候可通过下列方法调试，如果红光为点，请参照线变点处理方案，因为不摆动的时候也有可能会偏2.如果从保护镜那边看到是一团光而非一条线，则考虑是否为反射镜断裂3.请务必确认15V电源状态是正常Please note that:1. Only when the red light forms a line can the following method be u...
超强焊接系统的授权功能，可对设备进行使用时长授权，当设备使用超过其设定的时间，则显示授权终止The authorization function of the super welding system allows for the authorization of equipment usage duration. When the equipment is used beyond its ...
请认真阅读刷卡时的注意事项，非正常操作可能会导致刷卡异常本文适用屏幕花屏，闪屏，重影，重叠，触摸不灵敏等屏幕异常情况的处理Please read the precautions carefully when swiping the card, abnormal operation may cause abnormal card swipingThis article is suitable ...
鱼鳞纹的实现有两种一.通过系统的自带的点焊功能二.送丝机脉冲送丝（超强伟业带脉冲功能的送丝机）There are two ways to achieve fish scale pattern1. Through the system's built-in spot welding functionII. Pulse wire feeder (wire feeder with pulse fu...
超强伟业焊接头的切割设置Cutting settings for ultra-strong welding joints一.铜嘴使用切割铜嘴（建议铜嘴1.5以上）One brass mouthpieceUse a cutting copper nozzle (it is recommended to use a copper nozzle of 1.5 or above)二.工艺二.work...
一.参数的设置首页的焊接模式选择：连续，并设置工艺，调整好需要的焦点和铜嘴（工艺的参考数值可以在我们工艺里查看）One. parameterWelding mode selection on the first page: continuous, and set the process, adjust the required focus and copper nozzle(The refe...
焊接时遵循以下原则①板材越厚，焊丝越粗，功率越大，送丝速度越慢②功率越低，焊接面越白，功率越大，焊缝从彩色变黑色，此时单面成形。③焊丝的粗细选择应不大于板厚偏向于板厚，焊丝影响焊缝的饱满程度④焊丝越细，扫描宽度越低Follow the following principles when welding① The thicker the plate, the thicker the weldi...
一.铜嘴的使用铜嘴的分类主要区分：是否送丝，焊丝的大小，焊接角度，如上图所示，如内角送丝焊接1.0的焊丝则使用AS-12的铜嘴The classification of the copper nozzle is mainly divided into: whether the wire is fed, the size of the welding wire, and the welding...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...
注意：be careful:1.更换时请注意现场环境，建议拆掉在办公室等相对环境较好的地方更换Please pay attention to the on-site environment during replacement. It is recommended to remove it and replace it in a relatively good environment suc...